Zip HydroTap 3 In 1 HT1737UK (BH160G4) And HT1738UK (BH240G4)

Zip HydroTap 3 In 1

Boiling, filtered drinking water PLUS hot, cold (ambient) or mixed warm water – all from a single source

Benefits

Zip HydroTap 3-in-1 offers all of the advantages of a standard HydroTap plus these five outstanding benefits

Features Of The Zip Hydrotap 3 In 1

Buy Zips Commercial 3 In 1 HydroTap Online From The Uk's Largest Authorised Zip Dealer

For more details and to buy online, please visit the Zip Hydrotap Commercial 3 In 1 section on our main website or click on the links below
(Opens new window).

Zips Commercial Range Of 3 In 1 HydroTaps And Filtration

Zip Hydrotap 3 In 1 BH160G4 Zip Hydrotap 3 In 1 BH240G4 Zip Hydrotap FL2300KIT Zip Hydrotap FL3600KIT
Zip Hydrotap FL6000KIT Zip FL2300 Replacement Filter Zip FL3600 Replacement Filter Zip FL6000 Replacement Filter

Boiling system

Open outlet, vented system designed to operate at 98°C.

Hot water system

Delivers water at up to 55°C.

A choice of two programmable energy saving modes

Integral 24 hour 7 day timer enables the boiling and chilled water units to switch off automatically during known periods of inactivity e.g. overnight or weekends, but return to full functionality ahead of the next expected demand.

Inactivity Sleep Mode enables the boiling water unit to power down or switch off after 2 hours of non-use. Powering down allows the water temperature to gradually reduce to 65°C, at which it is maintained. Upon further draw off boiling resumes.

Filtration system

Integral triple action sub-micron fully encapsulated. Optional scale filtration system.

HydroTap head

Chrome plated tap with electronic controls, integral safety lock and LED indicators.

Mixer Tap head

Flick mixer action providing blended hot water and ambient mains cold water.

Undersink system

Corrosion resistant white enamelled steel case with front access door and control panel.

Installation

Location: The Mixer Tap should be located on a suitable sink. The HydroTap should be positioned either on a suitable sink or on the optional Zip Tap Font. Under-sink unit should be sited directly under the taps - maximum 1 metre away. It must be installed with clearances of 50mm to the left and right and 65mm at rear.

Plumbing: Designed for connection to a potable cold water supply with a minimum pressure of 2 bar and a maximum pressure of 7 bar. A pressure reducing valve to be fitted if pressure is greater than 7 bar.

An isolating valve should be installed between the supply and the unit.

Venting: A vent in the HydroTap may discharge small amounts of water or steam, so tap must be mounted where it can drain.

Ventilation-IMPORTANT: It is essential that the cupboard containing the undersink unit is adequately ventilated as poor air circulation will adversely affect the performance of the HydroTap. Cupboard doors must be offset all round using the 4mm buffers provided and the supplied vent fitted.

Electrical: To be wired to a double pole fused spur, minimum break capacity of 13 amps. Installation must comply with current IEE regulations.

General: The Zip HydroTap 3-in-1 and 4-In-1should be installed by a suitable qualified tradesperson and in accordance with the installation instructions.

Caution: In some hard water areas where mineral scale accumulation may be an issue, consideration should be given to the maintenance required. We recommend the use of Zip Scale Filtration System.

Warranty: 1 year on-site parts and labour. For full details visit www.zipheaters.co.uk/warranty

Technical Support: Contact Zip on Tel: 0800 077 8302.

Zip HydroTap 3 In 1 Installation

Contact Us Today

For more information give us a call on 01462 851103.